To those of you who own this model, I'd love to get some help! It's on order but currently somewhere in the middle of the Atlantic and I'm looking to get a nice case for it. Pretty sure I found one but need the actual dimensions of the car to see if will be a good fit. Based on the owners manual, I know it's 10.75" long, but really need the a couple more measurements. I'd like to display it with the engine cover off and prompted up in the corner of the case. Because of this, I'm considering a 1/12th case.
It would be greatly helpful, if a current owner of this model could take a few measurements and post them up. Here is what I'm looking for...
- Confirmation of 10.75" length
- Width car at its widest point
- Height of engine cover whilst standing on its end (back of rear wing to furthest point on side body panel)
I tried to post a pic I created (*png format) that illustrates the actual measurement I'm looking for...but don't know how, lol!
Thanks in advance and I look forward to seeing your responses!
Autoart Pagani Zonda Revolucion (78271) - Measurements
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
Hi, I think I could help. Measurements were based on M#78273 which is essentially the same car.
Lenght ~ 10.75"
Width ~ 4.6"
Rear Cover Height ~ 4.9"
Lenght ~ 10.75"
Width ~ 4.6"
Rear Cover Height ~ 4.9"
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
You are a rock star! Very much appreciated!
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
Great advice...my plan was to either find or have a stand created that could hold it properly upright. I'm thinking something like this (found in a Schmee150 BC youtube video). Any thoughts on where I could have one of these commissioned?
Last edited by Wbgoode77 on Wed Apr 22, 2020 3:57 pm, edited 1 time in total.
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
My images don't appear to be working??? Using the "IMG" link from PhotoBucket???
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
I see the images. You need to figure out how not to stress the fins. I guess if there is secondary support system you're okay.
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
Any chance I could get you to snap a picture of the underside of the engine cover? Looking to have a custom stand built and need to better understand the underneath structure. Thx in advance!
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
Here. I believe something can be fabricated. Two metal pins on outer edge connection point upper middle section.
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
Let us see the final results when you're done!
I have one too (#78272) and I'm always thinking of different ways to present it's full beauty.
And tell me if there is any help I can do.
I have one too (#78272) and I'm always thinking of different ways to present it's full beauty.
And tell me if there is any help I can do.
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
My Atlantic Case finally arrived and got my customer engine cover stand from PRDMinatures all set up...I’m pleased with the outcome.
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
That looks stellar! Final cost?
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
AutoArt Pagani Zonda Revolucion - $518
Atlantic Case - $134
PRD Minatures Engine Cover Stand - $85
Total - $737
but...
It will be my centerpiece in my new home office!
Atlantic Case - $134
PRD Minatures Engine Cover Stand - $85
Total - $737
but...
It will be my centerpiece in my new home office!
Re: Autoart Pagani Zonda Revolucion (78271) - Measurements
Not bad!
I can appreciate that tooIt will be my centerpiece in my new home office!